Prepare with HP HP0-Y51 exam practice material, pass for sure

A company has an Employees SSID, which enforces Wi-Fi Protected Access 2 (WPA2) with 802.1X. The company has a Contractors SSID, which has no encryption. Contractors can connect their own devices to the Contractors SSID and log in the credentials assigned to them by an employee. HP User Access Manager (UAM) has these services:
-AContractor access service, which is assigned to contractor accounts created by employees -An Employee access service, which is assigned to employee accounts synchronized from Active
Directory (AD)
A new company policy encourages contractors to use encryption. Contractors should download certificates when they connect to Contractors SSID and register. Then the contractors can connect to the Employees SSID and have an encrypted connection.
How does the administrator enable the contractors to connect to the Employees SSID but receive the correct contractor VLAN assignment?

• A. In the Employee access service, bind the Contractor group to an access policy that specifies the contractor VLAN ID and PAP authentication.
• B. In the Employee access service, bind the Contractor group to an access policy that specifies the contractor VLAN ID and EAP-TLS certificate authentication
• C. In the Contractor access service, bind the Employees SSID to an access policy that specifies the contractor VLAN ID and EAP-TLS certificate authentication
• D. In the Contractor access service, bind the Employees SSID to an access policy that specifies the contractor VLAN ID and PAP authentication

Refer to the exhibit.

A company has many dual-radio APs that are deployed relatively closely together. They are controlled by an HP Unified Wired-Wireless controller. The administrator wants to implement load balancing among the radios on different APs.
How should the administrator implement load balancing?

• A. Implement AP-based load balancing on the individual APs.
• B. Implement AP-based load balancing on the radios of the individual APs.
• C. Implement group-based load balancing by adding radios on different APs to the group.
• D. Implement radio-based load balancing by adding APs to the radio templates.

Table of acronyms

Refer to the exhibit.

An administrator is setting up an MPLS and L2VPN virtual circuit (VC) between customer Site 1 and Site 2. The administrator is creating a global cross-connect group, which uses LDP signaling, on PE-1. Which two elements are required to do this?

• A. A peer (PE-2) and a VLAN ID (access VLAN or. g1/0/1)
• B. An AC connection (specifies a service instance on g1/0/1) and a peer (PE-2)
• C. A peer (PE-2) and a VPN instance (associated with g1/0/1)
• D. An AC connection (specifies a service instance on g1/0/1) and a VPN instance (associated with g1/0/1)

What is one benefit of the HP patent for Adaptive Multicast channel width and Guard Interval 802.11n?

• A. HP APs can transmit multicasts as broadcasts or unicasts, helping to ensure higher transmission rates and more reliable delivery for multicast.
• B. HP APs can adapt the precise frequency on which they transmit to each client, enabling them to transmit multicasts to more than one clients at the same time.
• C. HP APs can adjust whether they send multicasts over a bonded channel based on the 802.11 standards supported on device in the current environment.
• D. HP APs can bind up to three channels together for any multicast transmissions in the 5 GHz frequency range, including 802.11a and 802.11n.

Table of Acronyms An administrator has configured an HP Comware switch to support FCoE in Fibre Channel Forwarder (FCF) mode. A switch interface, ten1/0/1, connects to a sewer FC host bus adapter (HBA), The HBA should send storage traffic in VSAN 2, which is associated with VLAN 20.

How should the administrator assign FC traffic for this HBA to VSAN 2?

• A. By binding a VFC interface to ten1/0/1 and specifying VSAN 2 as the VFC interface trunk VSAN
• B. By accessing the VLAN 20 configuration view and specifying ten1/0/1 as a member port of the VLAN
• C. By accessing the VSAN 2 configuration view and adding ten1/0/1 as a trunk port
• D. By configuring ten1/0/1 as an F-mode FC port and specifying VSAN2 as the port access VSAN