[Aug 30, 2021] 200-301 Ultimate Study Guide - Test4Sure [Q21-Q45]

[Aug 30, 2021] 200-301 Ultimate Study Guide - Test4Sure

Ultimate Guide to Prepare 200-301 Certification Exam for CCNA in 2021

NEW QUESTION 21
Drag and drop the AAA functions from the left onto the correct AAA services on the right

Answer:

Explanation:

NEW QUESTION 22

Refer to the exhibit. After the configuration is applied, the two routers fail to establish an OSPF neighbor relationship. what is the reason for the problem?

A. The OSPF router IDs are mismatched.
B. The network statement on Router1 is misconfigured.
C. Router2 is using the default hello timer.
D. The OSPF process IDs are mismatched.

Answer: C

NEW QUESTION 23
Refer to the exhibit.

After the switch configuration, the ping test fails between PC A and PC B.
Based on the output for switch 1, which error must be corrected?

A. There is a native VLAN mismatch.
B. The PCs are in the incorrect VLAN.
C. All VLANs are not enabled on the trunk.
D. Access mode is configured on the switch ports.

Answer: A

NEW QUESTION 24
Which security program element involves installing badge readers on data-center doors to allow workers to enter and exit based on their job roles?

A. multifactor authentication
B. biometrics
C. role-based access control
D. physical access control

Answer: B

Explanation:
Explanation
Access control readers give access to the building based on established credentials. Things like a key card, key fob, or biometrics like fingerprints are all considered established credentials.

NEW QUESTION 25
Which two functions are performed by the core layer in a three-tier architecture? (Choose two.)

A. Police traffic that is sent to the edge of the network
B. Inspect packets for malicious activity
C. Provide direct connectivity for end user devices
D. Ensure timely data transfer between layers
E. Provide uninterrupted forwarding service

Answer: D,E

Explanation:
Section: Network Fundamentals
Explanation/Reference: https://www.mcmcse.com/cisco/guides/hierarchical_model.shtml

NEW QUESTION 26
Which two functions can be performed by local DNS server? (choose two)

A. resolving names locally
B. transferring split horizon traffic between zones
C. assigning IP addresses to local clients
D. copying updated IOS images to cisco switches
E. forwarding name resolution requests to an external DNS server

Answer: A,E

NEW QUESTION 27
Refer to the exhibit.

Which password must an engineer use to enter the enable mode?

A. adminadmin123
B. default
C. cisco123
D. testing 1234

Answer: D

Explanation:
Explanation
If neither the enable password command nor the enable secret command is configured, and if there is a line password configured for the console, the console line password serves as the enable password for all VTY sessions -> The "enable secret" will be used first if available, then "enable password" and line password.

NEW QUESTION 28
Refer to the exhibit.

An administrator configures four switches for local authentication using passwords that are stored in a cryptographic hash. The four switches must also support SSH access for administrators to manage the network infrastructure. Which switch is configured correctly to meet these requirements?

A. SW1
B. SW2
C. SW3
D. SW4

Answer: C

NEW QUESTION 29
Which two of these statements regarding RSTP are correct? (Choose two.)

A. RSTP is a proprietary implementation of IEEE 802.1D STP.
B. RSTP defines new port roles.
C. RSTP is compatible with the original IEEE 802.1D STP.
D. RSTP defines no new port states.
E. RSTP cannot operate with PVST+.

Answer: B,C

NEW QUESTION 30
Which command should you enter to verify the priority of a router in an HSRP group?

A. show hsrp
B. show sessions
C. show interfaces
D. show standby

Answer: D

Explanation:
Section: IP Connectivity
Explanation:
The following is sample output from the show standby command:

NEW QUESTION 31
An engineer configures interface Gi1/0 on the company PE router to connect to an ISP Neighbor discovery is disabled

Which action is necessary to complete the configuration if the ISP uses third-party network devices?

A. Disable autonegotiation
B. Disable Cisco Discovery Protocol on the interface
C. Enable LLDP globally
D. Enable LLDP-MED on the ISP device

Answer: D

NEW QUESTION 32
Refer to the exhibit.

What does router R1 use as its OSPF router-ID?

A. 192.168.0.1
B. 10.10.10.20
C. 172.16.15.10
D. 10.10.1.10

Answer: C

Explanation:
Explanation
OSPF uses the following criteria to select the router ID:1. Manual configuration of the router ID (via the
"router-id x.x.x.x" command under OSPF router configuration mode).2. Highest IP address on a loopback interface.3. Highest IP address on a non-loopback and active (no shutdown) interface.

NEW QUESTION 33
Refer to the exhibit.

A packet is being sent across router R1 to host 172.16.0.14. What is the destination route for the packet?

A. 209.165.200.254 via Serial0/0/0
B. 209.165.200.254 via Serial0/0/1
C. 209.165.200.250 via Serial0/0/0
D. 209.165.200.246 via Serial0/1/0

Answer: B

NEW QUESTION 34
Refer to the exhibit. After you apply the given configuration to a router, the DHCP clients behind the device cannot communicate with hosts outside of their subnet. Which action is most likely to correct the problem?

A. Activate the dhcp pool
B. Correct the subnet mask
C. Configure the default gateway
D. Configure the dns server on the same subnet as the clients

Answer: C

NEW QUESTION 35
Which technology must be implemented to configure network device monitoring with the highest security?

A. NetFlow
B. SNMPv3
C. IP SLA
D. syslog

Answer: A

NEW QUESTION 36
Refer to the exhibit.

Router R2 is configured with multiple routes to reach network 10 1.1 0/24 from router R1. What protocol is chosen by router R2 to reach the destination network 10.1 1 0/24?

A. static
B. eBGP
C. EIGRP
D. OSPF

Answer: A

NEW QUESTION 37
What is a function of Wireless LAN Controller?

A. monitor activity on wireless and wired LANs
B. use SSIDs to distinguish between wireless clients.
C. register with a single access point that controls traffic between wired and wireless endpoints.
D. send LWAPP packets to access points.

Answer: B

NEW QUESTION 38
Refer to the exhibit.

Drag and drop the networking parameters from the left onto the correct values on the right.

Answer:

Explanation:

Explanation

NIC vendor OUI -> 00:0C:22NIC MAC address -> 00:0C:22:83:79:A3default gateway -> 192.168.1.193host IP address -> 192.168.1.200subnet mask -> 255.255.255.192 The "ip route" and "ip addr show eth1" are Linux commands.+ "ip route": display the routing table+ "ip addr show eth1": get depth information (only on eth1 interface) about your network interfaces like IP Address, MAC Address information

NEW QUESTION 39
Refer to the exhibit.

A router reserved these five routes from different routing information sources.
Which two routes does the router install in its routing table? (Choose two)

A. RIP route 10.0.0.0/30
B. OSPF route 10.0.0.0/16
C. iBGP route 10.0.0.0/30
D. OSPF route 10.0.0.0/30
E. EIGRP route 10.0.0.1/32

Answer: D,E

NEW QUESTION 40
Refer to the exhibit.

An engineer is tasked with verifying network configuration parameters on a client workstation to report back to the team lead. Drag and drop the node identifiers from the left onto the network parameters on the right.

Answer:

Explanation:

NEW QUESTION 41
Refer to the exhibit.

Which action is expected from SW1 when the untagged frame is received on the GigabitEthernet0/1 interface?

A. The frame is processed in VLAN 5.
B. The frame is processed in VLAN 11
C. The frame is dropped
D. The frame is processed in VLAN 1

Answer: A

NEW QUESTION 42
You have configured a router with an OSPF router ID, but its IP address still reflects the physical interface.
Which action can you take to correct the problem in the least disruptive way?

A. Specify a loopback address
B. Reboot the router
C. Save the router configuration
D. Reload the OSPF process

Answer: D

Explanation:
Section: IP Connectivity
Explanation:
Once an OSPF Router ID selection is done, it remains there even if you remove it or configure another OSPF Router ID. So the least disruptive way is to correct it using the command "clear ip ospf process".

NEW QUESTION 43
Drag and drop the network protocols from the left onto the correct transport services on the right.