May 08, 2022 Detailed New NSE7_OTS-6.4 Exam Questions for Concept Clearance
NSE7_OTS-6.4 Exam Preparation Material with New NSE7_OTS-6.4 Dumps Questions.
NEW QUESTION 13
An OT network architect must deploy a solution to protect fuel pumps in an industrial remote network. All the fuel pumps must be closely monitored from the corporate network for any temperature fluctuations.
How can the OT network architect achieve this goal?
- A. Configure a fuel server on the corporate network, and deploy a FortiSIEM with a single pattern temperature performance rule on the remote network.
- B. Configure a fuel server on the remote network, and deploy a FortiSIEM with a single pattern temperature performance rule on the corporate network.
- C. Configure both fuel server and FortiSIEM with a single-pattern temperature performance rule on the corporate network.
- D. Configure a fuel server on the remote network, and deploy a FortiSIEM with a single pattern temperature security rule on the corporate network.
Answer: A
NEW QUESTION 14
An OT network architect needs to secure control area zones with a single network access policy to provision devices to any number of different networks.
On which device can this be accomplished?
- A. FortiEDR
- B. FortiSwitch
- C. FortiGate
- D. FortiNAC
Answer: D
NEW QUESTION 15
Refer to the exhibit.
Based on the Purdue model, which three measures can be implemented in the control area zone using the Fortinet Security Fabric? (Choose three.)
- A. FortiNAC for network access control
- B. FortiEDR for endpoint detection
- C. FortiGate for application control and IPS
- D. FortiSIEM for security incident and event management
- E. FortiGate for SD-WAN
Answer: A,C,D
NEW QUESTION 16
An OT supervisor has configured LDAP and FSSO for the authentication. The goal is that all the users be authenticated against passive authentication first and, if passive authentication is not successful, then users should be challenged with active authentication.
What should the OT supervisor do to achieve this on FortiGate?
- A. Enable two-factor authentication with FSSO.
- B. Under config user settings configure set auth-on-demand implicit.
- C. Configure a firewall policy with LDAP users and place it on the top of list of firewall policies.
- D. Configure a firewall policy with FSSO users and place it on the top of list of firewall policies.
Answer: B
NEW QUESTION 17
Refer to the exhibit.
Which statement about the interfaces shown in the exhibit is true?
- A. The VLAN ID of port1-vlan1 can be changed to the VLAN ID 10.
- B. port1-vlan10 and port2-vlan10 are part of the same broadcast domain
- C. port2, port2-vlan10, and port2-vlan1 are part of the software switch interface.
- D. port1, port1-vlan10, and port1-vlan1 are in different broadcast domains
Answer: D
NEW QUESTION 18
What can be assigned using network access control policies?
- A. Profiling rules
- B. Layer 3 polling intervals
- C. Logical networks
- D. FortiNAC device polling methods
Answer: A
NEW QUESTION 19
When you create a user or host profile, which three criteria can you use? (Choose three.)
- A. Administrative group membership
- B. An existing access control policy
- C. Host or user attributes
- D. Location
- E. Host or user group memberships
Answer: C,D,E
NEW QUESTION 20
An OT administrator configured and ran a default application risk and control report in FortiAnalyzer to learn more about the key application crossing the network. However, the report output is empty despite the fact that some related real-time and historical logs are visible in the FortiAnalyzer.
What are two possible reasons why the report output was empty? (Choose two.)
- A. The administrator selected the wrong devices in the Devices section.
- B. The administrator selected the wrong time period for the report.
- C. The administrator selected the wrong logs to be indexed in FortiAnalyzer.
- D. The administrator selected the wrong hcache table for the report.
Answer: B,D
NEW QUESTION 21
When device profiling rules are enabled, which devices connected on the network are evaluated by the device profiling rules?
- A. Rogue devices, each time they connect
- B. All connected devices, each time they connect
- C. Known trusted devices, each time they change location
- D. Rogue devices, only when they connect for the first time
Answer: D
NEW QUESTION 22
What triggers Layer 2 polling of infrastructure devices connected in the network?
- A. A matched security policy
- B. A matched profiling rule
- C. A linkup or linkdown trap
- D. A failed Layer 3 poll
Answer: C
NEW QUESTION 23
Refer to the exhibit.
An OT architect has implemented a Modbus TCP with a simulation server Conpot to identify and control the Modus traffic in the OT network. The FortiGate-Edge device is configured with a software switch interface ssw-01.
Based on the topology shown in the exhibit, which two statements about the successful simulation of traffic between client and server are true? (Choose two.)
- A. The FortiGate-Edge device must be in NAT mode.
- B. Port5 is not a member of the software switch.
- C. The FortiGate devices is in offline IDS mode.
- D. NAT is disabled in the FortiGate firewall policy from port3 to ssw-01.
Answer: A,C
NEW QUESTION 24
Refer to the exhibit.
Given the configurations on the FortiGate, which statement is true?
- A. FortiGate is configured with forward-domains to forward only domain controller traffic.
- B. FortiGate is configured with forward-domains to filter and drop non-domain controller traffic.
- C. FortiGate is configured with forward-domains to forward only company domain website traffic.
- D. FortiGate is configured with forward-domains to reduce unnecessary traffic.
Answer: D
NEW QUESTION 25
What two advantages does FortiNAC provide in the OT network? (Choose two.)
- A. It can be used for network micro-segmentation.
- B. It can be used for industrial intrusion detection and prevention.
- C. It can be used for device profiling.
- D. It can be used for IoT device detection.
Answer: A,C
NEW QUESTION 26
Refer to the exhibit.
Based on the topology designed by the OT architect, which two statements about implementing OT security are true? (Choose two.)
- A. FortiGate-3 and FortiGate-4 devices must be in a transparent mode.
- B. Micro-segmentation can be achieved only by replacing FortiGate-3 and FortiGate-4 with a pair of FortiSwitch devices.
- C. Firewall policies should be configured on FortiGate-3 and FortiGate-4 with industrial protocol sensors.
- D. IT and OT networks are separated by segmentation.
Answer: A,D
NEW QUESTION 27
......
Fortinet NSE7_OTS-6.4 Exam Syllabus Topics:
| Topic | Details |
|---|---|
| Topic 1 |
|
| Topic 2 |
|
| Topic 3 |
|
| Topic 4 |
|
NSE7_OTS-6.4 2022 Training With 36 QA's: https://www.test4sure.com/NSE7_OTS-6.4-pass4sure-vce.html
Fortinet NSE7_OTS-6.4 Certification Exam Questions: https://drive.google.com/open?id=18vd7EYqkD4kxKio1lcvJ1JajIIYXlLGA